How deep should you lay pea gravel?

Add pea gravel to a depth of about 2-1/2 inches. Use a garden rake to smooth high spots and fill low spots as you go. Remember, the border should be about 1/2 inch higher than the gravel to help keep the small stones in place. If you need to tamp down the gravel, use a hand tamper.

Also, How much does a dump truck load of gravel cost?

A truck load of gravel costs $1,350 or more with a 10-yard minimum, including delivery and spreading based on the rock type, amount, truck size (double or tri-axle), and travel distance. Most rock-fill jobs use a 3-man crew plus a tractor for $46 per hour that spread 12 cubic yards per hour.

Hereof, Do you need landscape fabric under pea gravel?

A good landscape fabric beneath a layer of pebbles or gravel goes a long way in preventing weed seed germination. Even the best landscape fabric won’t stop 100% of the weeds. Some seeds will inevitably germinate and sprout, however having a weed block barrier will keep the roots from getting a foothold in the soil.

Also to know What should I put down before using pea gravel? Start with a heavy tamper to compress any soil underneath, add a sturdy base layer of either crushed rock or sand, layer on about 3 inches of pea gravel, and then tamp down again to make sure everything is compact. A sturdy base is especially important for gravel driveways.

Can you walk barefoot on pea gravel?

Pea gravel used for a walkway provides a softer surface to walk on compared with using a larger type of gravel. Walking on pea gravel barefoot is more bearable than walking on larger rocks which some times have jagged edges that can stab at feet.

Table of Contents

Crush and run is one of the cheapest materials that can be used in a gravel driveway at about $0.40 per square foot. Cost per cubic yard is about $20 and per ton about $28.

A commonly used gravel size for driveway base layers is #3 gravel. This rock is generally 1-2 inches in diameter and does double duty by establishing a solid, reliable foundation and providing adequate drainage; both critical factors in driveway construction.

Un-compacted Cloburn aggregates weigh 1.4 tonnes per cubic metre. Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres.

Depends on how thick you’re going to lay the gravel. If you’re only putting down an inch or two, normal foot traffic will eventually stir up the gravel such that in places you’ll see the underlying native soils mixing with the gravel. In that case, the fabric might be a good idea.


How to Keep Weeds From Growing Through the Pea Gravel


5 Landscape Fabric Alternatives

Installation: Pea Gravel in Flower Beds

Third, it’s not a good idea to install pea gravel directly on top of soil, so you’ll have to place landscaping fabric over the top soil. The fabric will help prevent weeds that could eventually displace the pea gravel, causing a not-so-appealing mess.

Cover the dirt with a 3-inch layer of coarse mulch made from cedar or pine bark. Cover the mulch with a single layer of weed block fabric. Adding underlayments between the rocks and the soil creates a weed barrier that helps prevent weed seeds from touching the soil.

If you have snow or mud on your shoes, then a pea gravel patio can be a problem as well. The small stones will stick to your soles in a manner similar to sprinkles on an ice cream cone.

Pea gravel is generally more expensive than organic mulches and, because of its weight, it is more difficult to install. … Your soil may retain moisture better with pea gravel than with no mulch at all, but the rock is not effective in maintaining even soil temperatures.

The main difference between these two types of gravel is the size of the rocks. Pea gravel, as its name implies, is small. Generally the stones are around 1/4th of an inch in diameter. … Crushed rock, on the other hand is a little bit larger in diameter around 1/2 to 1 inch.

Gravel. This is one of the cheapest alternatives to asphalt driveways by far, costing very little to have installed. … Gravel can be a somewhat permeable alternative to a concrete driveway, allowing some stormwater to pass through it.

Gravel is one of the cheapest driveway materials. Typically, it’s sold either by the cubic yard (a measure of volume) or by the ton (a measure of weight). The average cubic yard of gravel costs between $40 and $55. Expect to pay $50 to $65 per ton.

At a depth of 1 inch, the coverage is up to 240 square feet, and 3 inches can reduce the coverage rate to 80 square feet. One (1) ton of river rock covers approximately a 50-75 sq. ft.

How many square feet does a ton of gravel cover?


May 28, 2020


These are the best options for driveway surfaces gravel, because they are small stones combined with rock dust, which makes a more solid driving surface.

Gravel is typically graded by size, and most driveways use at least three different sizes of gravel that are put down in layers to create a solid foundation and ensure proper drainage. A popular choice for the bottom layer is #3 stone, which ranges in size from one to two inches in diameter.

How to convert tons of gravel to cubic yards. 1 cubic yard of gravel weight is 2800 lb, in United States, 1 ton of gravel is equal to 2000 pounds, convert tons of gravel to cubic yards = 2000/2800 = 0.714 cubic yards, so there are 0.714 cubic yards in a ton of gravel.


Ground preparation

As a rule of thumb 1 of our 25kg bags will cover an area of 0.25m to a recommended depth of 50mm.

Dump Truck Cubic Yardage – The Basics

While there is room for variance, most full-size dump trucks have a capacity of between 10 and 16 cubic yards.